Description:
(view full)
CAM-WOOD IAT 620-6-195 INVERTER DRIVEN FINGER JOINT SYSTEM WITH 102' INFEED AS AN OPTION and consisting of the following equipment:
Lay-Up and Block-Staging Infeed Conveyor:
- 24" wide x 31.5" long belt conveyor powered with 1/2 HP motors. Conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive.
FSR-62I Right Hand Inverter Type Finger Joint Shaper: - Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down.. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4” maximum shaper cutterhead diameter - without knives. 10HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades. Speed is controlled by system criteria
STC-62A Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: - 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeds at a constant rate of 180 FPM.
FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder: - Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" maximum shaper cutterhead diameter - without knives. 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades. Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and vary travel as needed. Speed is controlled by system criteria
Injection Type Glue Applicator: - Extrudes adhesive into the fingers without a messy runoff. 6" Comb height is standard. Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment)
STC-62A Single Table Conveyor Belt to the Assembly Section: - 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM.
FJ-500A (198") Assembly Press with Cut-Off Saw: - Capacity from 1" to 6” wide x 1/2" to 3" high x and from 6' to 16-1/2' long. A 2 HP motor powers the upper and a 2nd 2 HP motor powers lower pre-assembly/crowder rolls. With 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria. 5 HP - 2,850 RPM Cutoff saw accepts 14" dia. x 120 tooth x 4 mm kerf blade. Cutoff Saw can be set for up to (3) lengths. 5 HP Hydraulic power pack for final squeeze. Capacity from 1 to 4 table loads per minute.
Optional Equipment: - SFJ-IF-102; System arranged for up to 102" maximum incoming board lengths, all 31.5" long conveyor are increased in length to accept 102" inbound boards, add ...$16,800
- 8” Finished Width at Assembly Press, (horizontal joints only), add $9,900
- SFJ-IL-40 40” High Speed Material Infeed Conveyor System, add $12,600.00
- PC-66 Auto Feed Magazine 26” wide x 39.5” long, add $31,900.00.
- FJ-7000 24' Finished Length, add $9,900.00.
- 30 HP Increase Shaper Motor for longer joints, add $3,200.00.
- SFJ-C2 Complete Enclosures for both Shaper Sections, add $8,500.00.
- Unlimited Length Assembly Presses are Available. (Call Jeff at ext. 349 for pricing)
- Motor Control Center with under-voltage and overload protection; includes UL and CSA approved electrical components. Electric parts only, not the complete machine.
|
alt = 'New CAM-WOOD IAT 620-6-195 FINGER JOINTER (MEDIUM PRODUCTION)' title='New CAM-WOOD IAT 620-6-195 FINGER JOINTER (MEDIUM PRODUCTION)'/>
